[mrtanz]

Hi All,

I have been through the PDF with step by step instructions however after clicking "Code FDL" it runs through and gives me the following error:
Just trying to code our the disclaimer. The default was set to permanent so i set it to Kein_id.
Also the folder was named HU_CLAMP2. I could not find HU_CIC as per the cheat sheet
Car is 2012 328i

[HU_CHAMP2 - 63] prepareECUforCoding started
[HU_CHAMP2 - 63] prepareECUforCoding error
[HU_CHAMP2 - 63] finalizeECUCoding started
[HU_CHAMP2 - 63] finalizeECUCoding finished
[Exception - HU_CHAMP2 - 63] Exception occurred: job failed with negative response error:
code: written data does not match read data
description: no detailed description available; ECU: HU_CHAMP2_63_ETHERNET
severity: ERROR

Timestamp: Thu Jan 24 12:49:39 EST 2013
ErrorCategory: VEHICLE_ERROR ID: 433

[Frogman]

Originally Posted by mrtanz

Hi All,

I have been through the PDF with step by step instructions however after clicking "Code FDL" it runs through and gives me the following error:
Just trying to code our the disclaimer. The default was set to permanent so i set it to Kein_id.
Also the folder was named HU_CLAMP2. I could not find HU_CIC as per the cheat sheet
Car is 2012 328i

[HU_CHAMP2 - 63] prepareECUforCoding started
[HU_CHAMP2 - 63] prepareECUforCoding error
[HU_CHAMP2 - 63] finalizeECUCoding started
[HU_CHAMP2 - 63] finalizeECUCoding finished
[Exception - HU_CHAMP2 - 63] Exception occurred: job failed with negative response error:
code: written data does not match read data
description: no detailed description available; ECU: HU_CHAMP2_63_ETHERNET
severity: ERROR

Timestamp: Thu Jan 24 12:49:39 EST 2013
ErrorCategory: VEHICLE_ERROR ID: 433

This is the exact same error I got when trying to code with 48.3 using the old "Code Away" token.

You need to get a new E-Sys token. I also upgraded to 3.22.5 at the same time as the token is tied to the E-Sys release.

Read this thread here:

http://www.bimmerfest.com/forums/sho...7&postcount=46

[mrtanz]

Thanks
Where can i source the new token
i am on 3.18.4

[Frogman]

Originally Posted by mrtanz

Thanks
Where can i source the new token
i am on 3.18.4

You need to contact the poster of the thread I referenced.

[mrtanz]

Thanks everyone for your help
Problem is fixed with new token

[deniza]

Originally Posted by Frogman

This is the exact same error I got when trying to code with 48.3 using the old "Code Away" token.

You need to get a new E-Sys token. I also upgraded to 3.22.5 at the same time as the token is tied to the E-Sys release.

Read this:

I've bought both CIC and NBT modules just before my car was arrived. In ETK from 01 Dec 2012 F30 should be equipped with NBT headunit, but I found later in ETK from 01 Feb 2013 F30 car is equipped by ordinary CIC. May I install NBT anyway on my car and code it by using E-sys 3.18.4 with latest PSDZdata or do I need 3.22.5 to do coding?

My car was produced on 17 Jan 2013.

For now I have radio professional installed with small 6,5" display and standard instrument cluster (small LCD display).

Thanks.

[deniza]

Originally Posted by mrtanz

Thanks everyone for your help
Problem is fixed with new token

Mrtanz, do you have E-sys 3.22.5 with compatible pin to make a coding? I have 3.18.4, but as I read before it is not enougth to code cars start from 2013 year of production.